Home > Circular Loom
Circular Loom
2013-06-03
Circular loom warp shelves there are many spindles, according woven width and stretching the width of the specified range using the number of warp. Circular loom before entering warp by warp warp brown box to cross openings in the weft shuttle Cross through the opening in the circular motion of the warp knitting fabric into a tube. A shuttle circular loom a few put, there are a few woven into the weft Tong Shi for Woven, available flat looms, gripper, spray water loom weaving.
Earlier, the domestic circular loom are counterfeit imported circular loom, but the 1990s, this situation gradually changed, the birth of China's first circular loom with independent intellectual property rights, and in 1991, 1993, 1997 launched the second generation, third generation, fourth generation of circular loom, August 2000 set a number of successful development of more advanced technology in one of the world's first 10-Shuttle Circular Loom SPCL-10 super- / 6000, which is the fifth generation of circular loom, followed in January 2005, the world's first twelve shuttles super plastic circular loom was born and delivered to the user. Four years later, in November 2009, the world's first giant sixteen shuttle plastic circular loom SPCL-16/10000 order point of circular loom level has remained the world's leading
Circular loom circular loom maintenance practices and little knowledge
1 End Weft Sensor: regular cleaning detector cover (every four hours), the machine is running, ensure that white light has been lit, the infrared detector in accordance with the principles of design, dazzling lights will affect the performance of the sensor, as far as possible near the machine Alto tube using only sunlight, such as spindles shiny surface, the detector may not work correctly, avoid using aluminum bobbin or black yarn, black yarn detectors will not work.
2 weft sensors: circular loom in normal operation, when the weft breakage should be external reasons, the sensor detects the signal, to the controller, the control circular loom stop weft breakage if the machine can not automatically shut down: Jog the machine so that the yarn in which a shuttle running to the sensor tube beneath quickly snapped latitude manually, so that ball into the sensor's detection range, then the red LED does not light if the sensor, the sensor position should be adjusted until the red indicator light or replace the sensor.
3 main speed sensor: the normal operation of the machine, if you upgrade a large range of frequency hopping frequency, the sensor may be due to rotational vibrations of the host undetected, then need to adjust the position of the sensor, the sensor head aligned chainring then observed to enhance the frequency inverter, beating if to a lesser extent, then, several adjustments still can not achieve the desired effect, replace the sensor.
4. Enhance detection sensor: If man-machine interface can not accurately record production, testing the wiring is correct, if the wiring is correct, adjust the sensor position, run the machine, observe the indicator is blinking, if not flicker, consider replacing the sensor.
Earlier, the domestic circular loom are counterfeit imported circular loom, but the 1990s, this situation gradually changed, the birth of China's first circular loom with independent intellectual property rights, and in 1991, 1993, 1997 launched the second generation, third generation, fourth generation of circular loom, August 2000 set a number of successful development of more advanced technology in one of the world's first 10-Shuttle Circular Loom SPCL-10 super- / 6000, which is the fifth generation of circular loom, followed in January 2005, the world's first twelve shuttles super plastic circular loom was born and delivered to the user. Four years later, in November 2009, the world's first giant sixteen shuttle plastic circular loom SPCL-16/10000 order point of circular loom level has remained the world's leading
Circular loom circular loom maintenance practices and little knowledge
1 End Weft Sensor: regular cleaning detector cover (every four hours), the machine is running, ensure that white light has been lit, the infrared detector in accordance with the principles of design, dazzling lights will affect the performance of the sensor, as far as possible near the machine Alto tube using only sunlight, such as spindles shiny surface, the detector may not work correctly, avoid using aluminum bobbin or black yarn, black yarn detectors will not work.
2 weft sensors: circular loom in normal operation, when the weft breakage should be external reasons, the sensor detects the signal, to the controller, the control circular loom stop weft breakage if the machine can not automatically shut down: Jog the machine so that the yarn in which a shuttle running to the sensor tube beneath quickly snapped latitude manually, so that ball into the sensor's detection range, then the red LED does not light if the sensor, the sensor position should be adjusted until the red indicator light or replace the sensor.
3 main speed sensor: the normal operation of the machine, if you upgrade a large range of frequency hopping frequency, the sensor may be due to rotational vibrations of the host undetected, then need to adjust the position of the sensor, the sensor head aligned chainring then observed to enhance the frequency inverter, beating if to a lesser extent, then, several adjustments still can not achieve the desired effect, replace the sensor.
4. Enhance detection sensor: If man-machine interface can not accurately record production, testing the wiring is correct, if the wiring is correct, adjust the sensor position, run the machine, observe the indicator is blinking, if not flicker, consider replacing the sensor.